![fastcam mto fastcam mto](https://www.solvusoft.com/file-extensions/images/developers/316x280/1905_fastcam.png)
The MTO file is written by FastCamMTO, this is the Catalog Standard name Name, excluding item width in the case of type 2 and type 3 items. It is nevertheless recommended that an ItemID be suppliedĭata3 is mandatory text defining the Product
![fastcam mto fastcam mto](https://en.freedownloadmanager.org/screenshots/44552.jpg)
Note this is a special case differentįrom facility, drawing and assembly, where even though ITM_SPEC definesĪn ItemID, the entry is still optional, whereas it is mandatory for these Also see Data10 and Data11 below,ĭata2 is optional text for ItemID, and ifĮntered must comply with ITM_SPEC. When written by FastCamMTO, may alsoīe -1 (error) but NOT -2 (unchecked). Product Type as 0 (miscellaneous or unit item), 1 (long product item),Ģ (sheet item) or 3 (plate item). FIELDĭata1 is a mandatory integer number defining To apply to the current next higher level commodity until and higher levelĬommodity record or ENDMTO record occurrs. They may appear in any sequence, and continue Level commodity, either ASSEMBLY, DRAWING,įACILITY or JOB as determined by the records preceeding the JOB record These records apply to the current next higher Psuedo-mandatory and defaults to 1 if omitted.ĭata3. Until the next ASSEMBLY record or ENDMTO record.ĭata1 is mandatory text for AssemblyID which must This record is mandatory when required by ASS_SPEC, Until the next DRAWING record or ENDMTO record.ĭata1 is mandatory text for DrawingID which mustĭata2 is optional text defining Revision codeĪSSEMBLY, Data1, Data2 This record is mandatory when required by DRG_SPEC, Data6 are reserved for future useĭRAWING, Data1, Data2 If > 1 when FAC_SPEC specifies no quantities will raise an error.ĭata3. Until the next FACILITY record or ENDMTO record.ĭata1 is mandatory text for FacilityID which mustĭata2 is a numeric integer defining No.Off for All following records apply to this facility This record is mandatory when required by FAC_SPEC,Īnd prohibited otherwise. JOB records end at the ENDMTO record - see belowįACILITY, Data1, Data2 Of Folder in which all part data files are kept Only quantitative data records may nowĭata1 is optional text for JobID or JobNumberĭata2 is optional text for Job Descriptionĭata3 is optional text reserved for future definition This record flags the end of the 'specification' section of the file comprisingĪll the afforementioned records. This record is mandatory, but all data is optional. 0=no standardįittings, 1=numeric-only ID, 2=alpha-only ID Not, and if so how, ItemID for Standard Fittings is defined. This record is mandatory, blank or missing Data1ĭata1 is a numeric integer defining whether or Quantities, (all facilities are 1 off), 1=quantities as specifiedĭefault (quantities must be specified), any other value is ignoredĪre in total, 1=item quantities are per higher level commodity Or omitted) to define how quantities are defined or managed …
![fastcam mto fastcam mto](https://i.ebayimg.com/images/g/IJUAAOSw2QtdHxGg/s-l600.jpg)
The maximum number of characters used in commodity IDĭata3 is mandatory text describing the commodity,ĭata4 is a numeric integer flag (0 if blank If Data1 = 0, no further data is requiredĭata2 is a mandatory numeric integer defining Blank or missingĭata1 is a numeric integer defining the style Units may be Metric (Data1=0) or US (Data1=1) , If Data1 is blank orĭata1 is integer numeric and defines which unit If any optional annotation is required, use FASTCAMMMTO,COPYRIGHT FASTCAM INC 2003,Major,Minor,Revision,Language,Optional Major = Major Version number, Minor = Minor Version Number, Revision = Revision Number. THe copyright notice must be displayed as shown. Which defines any data following within that record.įASTCAMMTO,COPYRIGHT FASTCAM INC 2003,Major,Minor,Revision,Language If embedded spaces were used, they would preventĬorrect evaluation of numeric data and correct recognition of keywordsĮvery record is identified by a leading KEYWORD The alternative use of a single underscore character (ASCII Leading and trailing spaces are ignored for bothĮmbedded spaces are significant for text comparative Used as a decimal separator, must include such data within double quotation To contain a comma, including numeric data in locales where a comma is In the following, case is used only to promoteĬommas delimit data fields. Otherwise Case=CASE=cAse for comparative purposes.
#Fastcam mto software#
Software reading or writing the file may choose to reformat numeric dataĬase is respected for purposes of presentation Dates may be presented as text,Īnd boolean data as integer numbers, 0=false, 1=true. Such as Date, Boolean are not recognized. Permitted, other than CR/LF sequences appearing at ends of records.ĭata is either Text or Numeric only. Only ASCII characters 32 to 126 inclusive are